Pac SWI-JACK Bedienungsanleitung PDF herunterladen

06-08-09

SWI-JACK

Universal Steering Wheel Control Interface

Before You Start

A. Is this product compatible with the vehicle?

• See application guide (separate sheet) for listing of vehicles and connection information. If not, please visit

http://www.pac-audio.com/swixprogramming/swixprogramming.asp for the most current list of compatible

vehicles.

B. Prepare for the installation.

• If possible, install the SWI-JACK while you are installing the new head unit. Keep in mind you may need to plug in

the factory stereo to locate certain wires; therefore do not complete the head unit installation until the SWI-JACK is

working properly.

• Plan a general installation location for both the SWI-JACK plug and the control body. Keep in mind that the sup-

plied wire harness is two feet long, and the 1/8" plug harness is three feet long.

• Use a multimeter or approved measuring device for checking vehicle circuits.

Pacific Accessory Corporation

SEEK

PRESET

AM FM

VOLUME

PLAY

MUTE

Power

Jack for the SWI-JACK

Steering wheel

audio control wire

To Kenwood or

OEM wired

remote control input

Installation Instructions

For Alpine, JVC, Clarion, Kenwood,

Valor, OEM & Blaupunkt OEM

Steering Remote Ready Radios

For Alpine, Clarion JVC, or Valor radios, connect the SWI-JACK 1/8" plug into the radio's Steering Wheel input

jack on back of radio or wire harness. For Kenwood, or OEM radios, connect the blue/yel wire to the Remote Input wire

(blue/yel for Kenwood, gray for OEM) of radio.

Blaupunkt radios with optional wireless remote inputs are supported by the SWI-JACK, however we do not

supply any connectors or support for Blaupunkt. It is up to the consumer or installer to supply this connector. Use

vehicle Connector Chart and use VW connector as reference. Connect the SWI-JACK's blue/yel wire to pin #11 of VW

connector. The connector you obtain may come with two of three pieces, however the connector (usually green) should

show pin #11 on it.

1 2 3 4 5 6 7 8

Inhaltsverzeichnis

Seite 1 - Installation Instructions

106-08-09SWI-JACK Universal Steering Wheel Control InterfaceBefore You StartA. Is this product compatible with the vehicle?• See application guide (s

Seite 2 - SWI-JACK

2SWI-JACKWiring ConnectionsStep 1.Connect the BLACK wire to ground (-).Verication: Wire or location registers a constant (-) when probed.Step 2.Conne

Seite 3

306-08-09Step 5.Refer to The Vehicle Application Guide. Note the INTERFACE Version Number next to the selected vehicle. Fill in the information below

Seite 4

4Step 18.Press and hold program-ming/mode button on SWI-JACK. LED will light.Step 19.Release programming/mode button. SWI-JACKSWI-JACKSWI-JACKYou only

Seite 5 - 06-08-09

506-08-09Programming the SWI-JACK to Control the Head Unit (cont.)The SWI-JACK must be programmed in the specic order shown in the chart below. If a

Seite 6

6SWI-JACKSWI-JACKStep 22.Release the button.The LED will turn on back on. Skip to Step 24.Step 24.If you need to program more buttons, repeat step 20

Seite 7 - Testing the SWI-JACK

706-08-09Testing the SWI-JACK(For Version #4 only) Test each Heater function of the steering wheel controls. The TEMP and FAN should work properly. Wh

Seite 8 - Troubleshooting Guide

8Troubleshooting GuideWorking on a new or unlisted vehicle?We are always looking for new vehicle information. If you’ve successfully completed the in

Kommentare zu diesen Handbüchern

Keine Kommentare

Pac SWI-JACK Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Autolautsprecher Pac SWI-JACK herunter. PAC SWI-JACK User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Autolautsprecher Pac SWI-JACK